The Importance Of Current Sense Resistor In Switch Mode Power Supply

Current sense resistor is usually located in the switch mode power supply section. Newer version of monitor-the b+ (boost) circuit also have this current sense resistor. If you repair electronic equipment especially the switch mode power supplies, the current sensing resistor is connected to the source pin of power FET (field effect transistor) and the other end to HOT GROUND. The value of current sense resistor is in the range of 0.1 ohm to about 1 ohm. The values are depends on the design of each power supply.

In monitor power supply where pulse width modulation (pwm) ic UC3842 are used. Pin 3 of this power ic is called I-sense which means current sense and this pin is connected to source pin of POWER FET. The purpose of this current sense circuit is for overcurrent protection. This circuit usually samples the voltage drop across a resistor in series with the switching fet transistor. If the current rises abnormally due to some short circuit in the secondary side such as a shorted secondary diode or horizontal output transistor (HOT), the voltage will exceed a reference level and shutdown the pulse generator which is the PWM ic. This circuit provides protection to components in the event a problem occurs. In some cases where overload happen-the power section will blow and most of the time the components changed are fuse, power fet, pwm ic, zener diode and current sense resistor.

Do you know that a small change in this current sense resistor value have a great impact on the secondary output? A little change in value say from 0.22 ohm to 0.44 ohm can caused your ouput voltage to drop into half! I have seen a lot of repairer can't detect this type of problem (low output voltage) due to that they used analog or digital meter that don't have the low ohms range. You can't differentiate if the low ohms resistor has its value changed by using normal meters. I personally use the Dick Smith ESR Meter which have the capabilities to check resistor value down to 0.01 ohm! If you don't have this special meter you may just direct replace the current sense resistor to see if the generated secondary output will back to normal voltage.

Another tip is that if the current sense resistor in the monitor B+ circuit have changed value it will caused the output in the boost circuit to become low and you will have a small width display and of course the high voltage will become low as well. Instead of 24Kv it becomes 15-18Kv.

Jestine Yong is a electronic repairer and a writer. For more information on electronic repair please visit his website at http://www.noahtec.com/electronic-repai r-articles.htm

Hardware obscolescnce is biggest storage problem
Canton Repository (subscription), OH - 16 hours ago
BY Jim Hillibish We now have about three decades of CD discs to judge their longevity. They seem to be holding up well, but there always will be doubts. ...

OCZ announces Gear site to sell EOL hardware
TechSpot - 1 hour ago
The reasoning seems to be simple enough: Too much hardware, not enough buyers – or too much old hardware taking plenty of space. The gear will still carry a ...

The US Federal Government Network Hardware Expenditures Report and ...
MarketWatch - Sep 5, 2008
The report defines network hardware as equipment purchased to connect PCs to one another in local area networks, as well as to connect locations/LANs via ...
Get a Greater Degree of Perspective on This Complex Market with US ... MarketWatch
US Education Information Technology Expenditures By Education ... MarketWatch
all 71 news articles

MorphOS on Apple Hardware
OS News - 1 hour ago
by Mage66 (1.92) on Sun 7th Sep 2008 19:51 UTC If MorphOS could be made to work on Apple Hardware (not just the G4 iMac), I have 3 B&W G3 computers that ...

Dawsonville Hardware September Bargains
Dawson Times, GA - 7 hours ago
Step into Dawsonville Hardware on the square in September for these bargains of the month. Dawsonville Hardware carries a large selection of hardware ...

Inventorspot
Russians Develop Hardware For Forecasting Earthquakes From Space
Inventorspot - Sep 6, 2008
According to news sources, Russian crew members of the International Space Station (ISS) have already installed the necessary hardware and scientific ...

Mix Hardware to reopen
Battle Creek Enquirer, MI - Sep 6, 2008
A hardware store on Battle Creek’s north side is under construction and expected to open around Thanksgiving, according to the store’s owner. ...
Eric J. Greene: How does the little guy make it? Battle Creek Enquirer
all 2 news articles

Ace Hardware opening in Rockwell
Salisbury Post, NC - 12 hours ago
He's opening a new Ace Hardware on Sept. 16 in the building at 229 E. Main St. that once housed an early Food Town grocery. The spot had remained vacant ...

Scientific American
Beyond the Ads, a Fevered Campaign to Improve Vista
RedOrbit, TX - 3 hours ago
Corps of Microsoft engineers, for example, have been dispatched to tweak hardware and software to make Vista PCs faster and less prone to crashing. ...
Windows Vista: The OS About Nothing InformationWeek
Microsoft Kicks off new Windows Campaign with Star Power Prdomain Business Register (press release)
The Bill and Jerry Show Macworld
Wall Street Journal - CNNMoney.comall 532 news articles

ZDNet
Netflix post-mortem: hardware failure and poor transparency
ZDNet - Sep 5, 2008
Massive shipping delays last month at Netflix were caused by hardware failure. Although diagnosing hardware problems can be tough, Netflix gets the dunce ...

Wind Chimes and more...

Windchimes for great gifts!

An Introduction to HD-DVD